Lawnmower manual cutting bar

Whether your acreages are small and crops light or large acreages with heavy crops, Rowse has a mower for your needs! When you choose the International Harvester Co. No pitmans, gears or connecting rods to cause problems. The Balanced Head converts speed and power to fast, powerful knife strokes. The IH Balanced Mower Head and Cutter Bar features a balanced head designed with just three moving parts, riding on six precision tapered roller bearings.

There are no pitmans, gears or connecting rods to cause problems. The balanced head converts speed and power to efficient sickle strokes. The sickle stays sharp longer, and runs at 2, strokes per minute for quick cutting action and faster travel through the field.

The balanced design keeps knife sections in register, parallel and exposed for sharp, even cutting over rough ground. An automatic safety release protects both heavy-duty sickle bars. The mower bar breaks away if it hits an obstruction, reducing the chance of machine damage.

Reel mowers have five twisted cutting blades arranged in a cylinder, reveals Home Depot. As you push the lawnmower, the blades spin and cut the grass against a fixed-position cutting bar at the base of the mower.

The blades and cutting bar must be positioned close together without touching. When adjusted correctly, the blades can cut a strip of paper cleanly, just as you would cut it with a pair of scissors. Set the reel mower on a table or work bench for easy access to the reel, advises Mother Earth News.

Chock the wheels with small wood blocks to prevent them from moving and turning the cutting blade cylinder. Spin the reel with your hand to determine the type of adjustment required. If you hear a metal scraping sound, adjust the blades away from the horizontal cutting bar. If the reel spins freely, move it closer to the cutting bar. Locate the four adjustment screws on the reel mower.

There is one screw on either side of the reel, and one screw on either side of the cutting bar. Insert a flat screwdriver in the screw slots on the sides of the blade reel, instructs YouTube.

Do not allow children to operate the machine. Allow only people who are responsible, trained, familiar with the instructions, and physically capable to operate the machine. Improperly using or maintaining this machine can result in injury.

To reduce the potential for injury, comply with these safety instructions and always pay attention to the safety-alert symbol, which means Caution, Warning, or Danger—personal safety instruction. Failure to comply with these instructions may result in personal injury or death. Safety decals and instructions are easily visible to the operator and are located near any area of potential danger.

Replace any decal that is damaged or missing. Important: Remove and discard the protective plastic sheet that covers the engine and any other plastic or wrapping on the machine. Important: To prevent accidental starting, do not insert the electric-start button into the electric-start ignition if equipped until you are ready to start the engine.

Important: Your machine does not come with oil in the engine, but it does come with a bottle of oil. Before starting the engine, fill the engine with oil. Always inspect the machine to ensure that the blades, blade bolts, and cutting assembly are not worn or damaged. Inspect the area where you will use the machine, and remove all objects that could interfere with the operation of the machine or that the machine could throw.

Adjusting the cutting height may bring you into contact with the moving blade, causing serious injury. Shut off the engine, remove the electric-start button electric-start model only , and wait for all moving parts to stop.

Fuel is extremely flammable and highly explosive. A fire or explosion from fuel can burn you and others and can damage property. Fill the fuel tank outdoors, in an open area, when the engine is cold.

Wipe up any fuel that spills. If you spill fuel, do not attempt to start the engine. Avoid creating a source of ignition until the fuel vapors have dissipated. Fuel is harmful or fatal if swallowed. Long-term exposure to vapors can cause serious injury and illness. Do not store fuel either in the fuel tank or in fuel containers over the winter unless fuel stabilizer has been added to the fuel. Fill the fuel tank with fresh unleaded regular gasoline from a major name-brand service station Figure 9.

Important: To reduce starting problems, add fuel stabilizer to the gasoline all season. Mix the stabilizer with gasoline less than 30 days old. Important: If the oil level in the crankcase is too low or too high and you run the engine, you may damage the engine. You can raise or lower the handle in 1 of 2 positions that is more comfortable for you Figure Loosen both handle knobs until you can push the square edges of the carriage bolts out of the square holes in the handle brackets.

Adjust the cutting height as desired. Set all wheels to the same cutting height Figure Wear appropriate clothing, including eye protection; long pants; slip-resistant, substantial footwear; and hearing protection. Tie back long hair, secure loose clothing, and do not wear jewelry.

The blade is sharp; contacting the blade can result in serious personal injury. Shut off the engine, remove the electric-start button electric-start model only , and wait for all moving parts to stop before leaving the operating position.

When you release the blade-control bar, the engine should shut off and the blade should stop within 3 seconds. If not, stop using your machine immediately and contact an Authorized Service Dealer. Keep bystanders, especially small children, out of the operating area.

Stop the machine if anyone enters the area. Operate the machine only in good visibility and appropriate weather conditions. Do not operate the machine when there is the risk of lighting. Wet grass or leaves can cause serious injury if you slip and contact the blade. Avoid mowing in wet conditions. Use extreme care when approaching blind corners, shrubs, trees, or other objects that may block your view.

Watch for holes, ruts, bumps, rocks, or other hidden objects. Uneven terrain could cause the machine to overturn or cause you to lose your balance or footing. Stop the machine and inspect the blades after striking an object or if there is an abnormal vibration in the machine. Make all necessary repairs before resuming operation. Before leaving the operating position, shut off the engine, remove the electric-start button electric-start model only , and wait for all moving parts to stop.

If the engine has been running the muffler will be hot and can severely burn you. Keep away from the hot muffler. Check the grass catcher components and the discharge chute frequently for any wear or deterioration and replace them with the manufacturer's recommended parts when necessary.

Mow across the face of slopes; never up and down. Use extreme caution when changing direction on slopes. You can start the engine using either the electric-start button if equipped or the recoil-start handle. Hold the blade-control bar against the handle A of Figure If the electric-start button has been removed, insert it in the electric starter B of Figure Push the electric-start button until the engine starts C of Figure Note: If the machine does not start after several attempts, contact an Authorized Service Dealer.

Pull the recoil-start handle B of Figure Note: When you pull the recoil-start handle, pull it lightly until you feel resistance, then pull it sharply. Allow the rope to return to the handle slowly.

To operate the self-propel drive, simply walk with your hands on the upper handle and your elbows at your sides, and the machine will automatically keep pace with you Figure Note: If the machine does not freely roll backward after self-propelling, stop walking, hold your hands in place, and allow the machine to roll a couple of centimeters inches forward to disengage the wheel drive.

You can also try reaching just under the upper handle to the metal handle and push the machine forward a couple of centimeters inches.

If the machine still does not roll backward easily, contact an Authorized Service Dealer. Note: Remove the electric-start button if equipped whenever you leave the machine. Important: When you release the blade-control bar, the engine should shut off and the blade should stop within 3 seconds. If they do not, stop using your machine immediately and contact an Authorized Service Dealer.

Your machine comes from the factory ready to recycle the grass and leaf clippings back into the lawn. If the grass bag is on the machine and the bag-on-demand lever is in the bagging position, move the lever to the recycling position; refer to Operating the Bag-on-Demand Lever. If the side-discharge chute is on the machine, remove it; refer to Removing the Side-Discharge Chute. If the bag-on-demand lever is in the recycling position, move it to the bagging position; refer to Operating the Bag-on-Demand Lever.

Raise and hold up the rear deflector A of Figure Install the grass bag, ensuring that the pins on the bag rest in the notches on the handle B of Figure To remove the bag, reverse the steps in Installing the Grass Bag. The bag-on-demand feature allows you to either collect or recycle grass and leaf clippings while the grass bag is attached to the machine. To bag the grass and leaf clippings , press the button on the bag-on-demand lever and move the lever forward until the button on the lever pops up Figure To recycle or side-discharge the grass and leaf clippings , press the button on the lever and move the lever rearward until the button on the lever pops up.

Important: For proper operation, shut off the engine, wait for all moving parts to stop, and then remove any grass clippings and debris from the bag-on-demand door and the surrounding opening Figure 18 before you move the bag-on-demand lever from 1 position to another. If the grass bag is on the machine and the bag-on-demand lever is in the Bagging position, move the lever to the Recycling position; refer to Operating the Bag-on-Demand Lever.

Lift up the side deflector and install the side-discharge chute A and B of Figure To remove the side-discharge chute, lift up the side deflector, remove the side-discharge chute, and lower the side-discharge deflector. Inspect the area where you will use the machine and remove all objects that the machine could throw.

If the machine strikes an object or starts to vibrate, immediately shut off the engine, disconnect the wire from the spark plug, remove the electric-start button if equipped , and examine the machine for damage. Cut only about a third of the grass blade at a time.

Do not cut below 51 mm 2 inches unless the grass is sparse or it is late fall when grass growth begins to slow down. When cutting grass over 15 cm 6 inches tall, mow at the highest cutting height setting and walk slower; then mow again at a lower setting for the best lawn appearance. If the grass is too long, the machine may plug and cause the engine to stall.

Wet grass and leaves tend to clump on the yard and can cause the machine to plug or the engine to stall. Be aware of a potential fire hazard in very dry conditions, follow all local fire warnings, and keep the machine free of dry grass and leaf debris. Alternate the mowing direction.

This helps disperse the clippings over the lawn for even fertilization. After cutting the lawn, ensure that half of the lawn shows through the cut leaf cover. You may need to make more than a single pass over the leaves.

If there are more than 13 cm 5 inches of leaves on the lawn, mow at a higher cutting height and then again at the desired cutting height. Never store the machine or fuel container where there is an open flame, spark, or pilot light, such as on a water heater or on other appliances. Shut off the engine and wait for all moving parts to stop before leaving the operating position.

Lower the machine to its lowest cutting-height setting. Refer to Adjusting the Cutting Height. Wash out the area under the rear door where the clippings go from the underside of the machine to the grass bag.

Note: Wash out the area with the bag-on-demand if equipped in both the fully forward and fully rearward positions. Attach a garden hose that is connected to a water supply to the washout port Figure Start the engine and run it for a few minutes to dry the underside of the machine to prevent it from rusting.

Folding or unfolding the handle improperly can damage the cables, causing an unsafe operating condition. Remove the electric-start button Figure Remove and save the 2 handle knobs and 2 carriage bolts from the handle brackets Figure Important: Route the cables to the outside of the handle knobs as you fold the handle.

Fold the handle by rotating it forward Figure Insert the carriage bolt with the bolt head toward the inside through the handle bracket and the upper hole in the handle end. Ensure that the square edges of each carriage bolt fits into the upper or lower square hole in its related handle bracket Figure To unfold the handle, refer to Assembling and Unfolding the Handle.

Disconnect the spark-plug wire from the spark plug and remove the electric-start button before performing any maintenance procedure. Wear gloves when servicing the blade. Do not repair or alter the blade s.

Tipping the machine may cause the fuel to leak.